http://ndiswrapper.sourceforge.net/wiki/index.php?action=history&feed=atom&title=Linksys_WPC54Gv2 2026-07-13T09:04:53Z Revision history for this page on the wiki MediaWiki 1.26.0 http://ndiswrapper.sourceforge.net/wiki/index.php?title=Linksys_WPC54Gv2&diff=520&oldid=prev 2009-07-23T13:46:43Z

<p>Created page with &#039;==Linksys WPC54G v2 54Mbps== * Chipset: Texas Instruments ACX 111 * pciid: 104c:9066 * Driver: Linksys ftp://ftp.linksys.com/pub/network/wpc54gv2_driver_utility_v2.02.zip ==In…&#039;</p> <p><b>New page</b></p><div>==Linksys WPC54G v2 54Mbps==<br /> * Chipset: Texas Instruments ACX 111<br /> * pciid: 104c:9066<br /> * Driver: Linksys ftp://ftp.linksys.com/pub/network/wpc54gv2_driver_utility_v2.02.zip<br /> <br /> ==Info==<br /> linux-2.6.8-gentoo kernel, ndiswrapper 0.10.Kept having kernel panic (interrupt-related) upon module load until I set CONFIG_PCI_MSI=y (and unset CONFIG_4KSTACKS, just in case.) Also, used <br /> <br /> ndiswrapper -i LSTINDS.INF<br /> <br /> (NOT lsbcmnds.inf). Works with 64 and 128-bit WEP. Sometimes need to repeat config info (and commit) repeatedly, else driver &amp; card will ignore requested setup. Also works with Gentoo 2.6.9-r9, ndiswrapper 0.12 and drivers that came from CD.<br /> <br /> NEW USER NOTE 12/30/05 by -JSK-: I had lots of problems getting the settings to take with this card and the above Windows driver. I finally found that the settings were timing and order dependent. Here is how I got the card to stick in Managed mode with 128 bit WEP and open authentication:<br /> <br /> ifconfig wlan0 essid $ESSID mode ad-hoc<br /> sleep 1<br /> iwconfig wlan0 key $KEY open<br /> sleep 1<br /> iwconfig wlan0 key open<br /> iwconfig wlan0 key on<br /> sleep 3<br /> iwconfig wlan0 essid $ESSID mode managed<br /> sleep 1<br /> iwconfig wlan0 key $KEY open<br /> sleep 1<br /> iwconfig wlan0 key open<br /> sleep 15<br /> ifconfig $DESIRED_IP_MASK_BROADCAST_ETC up<br /> <br /> I know it&#039;s a hack, but this script works every single time for me. Before, life was miserable. On debian, you can put this in a shell script and add a &quot;pre-up&quot; line in your interfaces file instead of using the &quot;wireless&quot; options. YMMV.<br /> <br /> Working fine on Ubuntu Breezy Badger (kernel 2.6.12) using ndiswrapper 1.9 / ndiswrapper-utils 1.7 and lstinds.inf driver. -- Johnmxl 10:45, 13 February 2006 (PST)<br /> <br /> Ndiswrapper is not needed. In Ubuntu Dapper (and probably in other Linux distributions as well) this card is supported natively with the acx driver. See http://ubuntuforums.org/showthread.php?t=75448 -- neu or http://ubuntuforums.org/showpost.php?p=1114757&amp;postcount=31 for a summary of the fix -- GigaClon<br /> <br /> <br /> [[Category:Linksys]]<br /> [[Category:PCI]]<br /> [[Category:WORKS]]<br /> [[Category:NATIVE]]</div>

Brinley